Single Board Computers
email:Info@TrentonTechnology.com
phone:(770) 287-3100
toll free:(800) 875-6031
fax:(770) 287-3150
Home About Us Products Technical Support New & Events White Papers SiteMap Contact Us International Sales


Technical Information
Support Request
Contact Tech Support
Certifications
White Papers
RoHS Product Chart

Printable Version

DP2/DP2GX (5664-xxx)
Jumpers      



5664tde
Jumpers


NOTE:
For two-position jumpers (3-post), "RIGHT" is toward the bracket end of the board; "LEFT" is toward the memory sockets.

* = default value


JU7 COMBO I/O (P5A) SPEAKER CONNECT
(Also refer to JU18 - Combo I/O Reset Connect.)
INSTALL= Connect speaker data signal to pin 8 of Combo I/O connector (P5A) *
REMOVE= Disconnect


JU8 PASSWORD CLEAR
INSTALL = Reset to null
REMOVE = Normal operation *

JU9 CRT TYPE SELECT
LEFT = Monochrome
RIGHT = Color *


JU10/JU11 SYSTEM FLASH ROM OPERATIONAL MODES
The Flash ROM has two programmable sections: the Boot Block for "flashing" in the BIOS and the Main Block for the executable BIOS and PnP parameters. Normally only the Main Block is updated when a new BIOS is flashed into the system.
JU10 JU11
Program All (Boot and Main) Right Right
Normal PnP (Program Main Block) Right * Left *
Write Protect Left Left


JU12 CMOS CLEAR
INSTALL = Clear CMOS
REMOVE = Operate *

NOTE: The CMOS Clear jumper works on power-up. To clear the CMOS, power down the system, install the jumper, then turn the power back on. CMOS is cleared during the POST routines. Then power down the system again and remove the jumper before the next power-up.


JU13 SCSI TERMINATION ENABLE
INSTALL= Disable on-board active termination for SCSI interface
REMOVE= Enable *


JU14 FAN SPEED MONITOR
This jumper must be removed (disabled).


JU15 3.3V MONITOR ENABLE
INSTALL = Enable 3.3V monitor
REMOVE = Disable monitor *

NOTE: JU15 enables the 3.3V monitor, which monitors the 3.3V power plane of the backplane. This voltage is routed to the SBC via the PICMG® connector. The monitor generates a RESET to the SBC if 3.3V is below tolerance. If your system does not supply 3.3V to the backplane, this jumper must be removed (disabled).


JU16 WATCHDOG TIMER
LEFT = Normal reset *
RIGHT = Enable watchdog


JU17 INTERRUPT 12 (IRQ12) SELECT
INSTALL = IRQ12 dedicated to PS/2 mouse *
REMOVE = IRQ12 available for system use




JU18 COMBO I/O (P5A) RESET CONNECT
(Also refer to JU7 = Combo I/O Speaker Connect.)
INSTALL= Connect reset data signal to pin 1 of Combo I/O connector (P5A) *
REMOVE= Disconnect


JU19 SCSI ACTIVITY LED ENABLE
INSTALL= Light the hard drive LED for SCSI drive activity*
REMOVE= No SCSI drive (i.e., the SCSI controller is not being used)


JU20 DUAL PROCESSOR ENABLE
INSTALL = Enable dual processor operation *
REMOVE = Single processor operation


CPU SPEED JUMPERS
There are four jumpers (W3, W4, W5 and W6) which must be set correctly to allow the SBC to take full advantage of the speed of the Pentium II/III microprocessor. These jumpers must be set as specified below.
CPU Synthesizer   Jumpers
Speed Frequency   W4* W3 W6 W5
850MHz 100MHz   In Out In Out
800MHz 100MHz   Out In In Out
750MHz 100MHz   Out Out Out In
700MHz 100MHz   Out In Out In
650MHz 100MHz   Out Out In In
600MHz 100MHz   Out In In In
550MHz 100MHz   In Out Out Out
500MHz 100MHz   In In Out Out
450MHz 100MHz   In Out In Out
400MHz 100MHz   In In In Out
350MHz 100MHz   In Out Out In
333MHz 66MHz   In In Out Out


ETHERNET LEDS AND CONNECTORS
The Ethernet interface has two LEDs for status indication and an RJ-45 network connector.
LED/Connector Description
Link Status LED Green LED which indicates the link status.
ON = The Ethernet interface has a valid link on the network connection and is ready for normal operation (10Base-T link or 100Base-TX link).
OFF = The Ethernet interface did not find a valid link on the network connection. Transmit and receive are not possible.
Activity LED Red LED which indicates the transmit or receive activity for the 10Base-T or 100Base-TX network connection.
ON = A packet is being transmitted or received.
OFF = There is no network activity.
RJ-45 Network Connector The RJ-45 network connector requires a category 5 Connector (CAT5) unshielded twisted-pair (UTP) 2-pair cable for a 100-Mb/s network connection or a category 3 (CAT3) or higher UTP 2-pair cable for a 10-Mb/s network connection

Connectors

NOTE:
Pin 1 on the connectors is indicated by the square pad on the PCB.

P2 - KEYLOCK CONNECTOR
5 pin single row header, Amp #640456-5
PIN SIGNAL
1 LED Power
2 Key
3 Gnd
4 Keylock Data
5 Gnd

P3 - FLOPPY DRIVE CONNECTOR
34 pin dual row header,
Robinson Nugent #IDH-34LP-S3-TR
PIN SIGNAL
1 Gnd
3 Gnd
5 Gnd
7 Gnd
9 Gnd
11 Gnd
13 Gnd
15 Gnd
17 Gnd
19 Gnd
21 Gnd
23 Gnd
25 Gnd
27 Gnd
29 Gnd
31 Gnd
33 Gnd
PIN SIGNAL
2 N-RPM
4 NC
6 D-Rate0
8 P-Index
10 N-Motoron 1
12 N-Drive Sel2
14 N-Drive Sel1
16 N-Motoron 2
18 N-Dir
20 N-Stop Step
22 N-Write Data
24 N-Write Gate
26 P-Track 0
28 P-Write Protect
30 N-Read Data
32 N-Side Select
34 Disk Chng

P4 - KEYBOARD CONNECTOR
6 pin mini DIN, Kycon #KMDG-6S-BS-PS
PIN SIGNAL
1 Kbd Data
2 Reserved
3 Gnd
4 Kbd Power (+5V fused) with self-resetting fuse
5 Kbd Clock
6 Reserved

P4A - KEYBOARD HEADER
5 pin single row header, Amp #640456-5
PIN SIGNAL
1 Kbd Clock
2 Kbd Data
3 Key
4 Kbd Gnd
5 Kbd Power (+5V fused) with self-resetting fuse

P5 - SPEAKER PORT CONNECTOR
4 pin single row header, Amp #640456-4
PIN SIGNAL
1 Speaker Data
2 Key
3 Gnd
4 +5V

P5A - COMBO I/O CONNECTOR
8 pin single row header, Amp #640456-8
PIN SIGNAL
1 Reset (See JU18 in Configuration Jumpers above.)
2 Gnd
3 NC
4 Kbd Clock
5 Kbd Data
6 Kbd Lock Data
7 Kbd Power (+5V fused) with self-resetting fuse
8 Speaker Data

P6 - SERIAL PORT 1 CONNECTOR
10 pin dual row header, 3M #30310-6002HB
PIN SIGNAL
1 Carrier Detect
3 Receive Data-I
5 Transmit Data-0
7 Data Terminal Ready-0
9 Signal Gnd
PIN SIGNAL
2 Data Set Ready-I
4 Request to Send-O
6 Clear to Send-I
8 Ring Indicator-I
10 NC

P7 - SERIAL PORT 2 CONNECTOR
10 pin dual row header, 3M #30310-6002HB
PIN SIGNAL
1 Carrier Detect
3 Receive Data-I
5 Transmit Data-0
7 Data Terminal Ready-0
9 Signal Gnd
PIN SIGNAL
2 Data Set Ready-I
4 Request to Send-O
6 Clear to Send-I
8 Ring Indicator-I
10 NC

P8 - PARALLEL PORT CONNECTOR
26 pin dual row header, 3M #30326-6002HB
PIN SIGNAL
1 Strobe
3 Data Bit 0
5 Data Bit 1
7 Data Bit 2
9 Data Bit 3
11 Data Bit 4
13 Data Bit 5
15 Data Bit 6
17 Data Bit 7
19 ACK
21 Busy
23 Paper End
25 Slct
PIN SIGNAL
2 Auto Feed XT
4 Error
6 Init
8 Slct In
10 Gnd
12 Gnd
14 Gnd
16 Gnd
18 Gnd
20 Gnd
22 Gnd
24 Gnd
26 NC

P9 - PS/2 MOUSE CONNECTOR
6 pin mini DIN, Kycon #KMDG-6S-BS-PS
PIN SIGNAL
1 Ms Data
2 Reserved
3 Gnd
4 Kbd Power (+5V fused) with self-resetting fuse
5 Ms Clock
6 Reserved

P9A - PS/2 MOUSE HEADER
6 pin single row header, Amp #640456-6
PIN SIGNAL
1 Ms Data
2 Reserved
3 Kbd Gnd
4 Kbd Power (+5V fused) with self-resetting fuse
5 Ms Clock
6 Reserved

P10 - EXTERNAL RESET CONNECTOR
2 pin header, Amp #640456-2
PIN SIGNAL
1 Negative External Reset
2 Gnd

P11 - PRIMARY IDE HARD DRIVE CONNECTOR
40 pin dual row header,
Robinson Nugent #IDH-40LP-S3-TR
PIN SIGNAL
1 Reset
3 Data 7
5 Data 6
7 Data 5
9 Data 4
11 Data 3
13 Data 2
15 Data 1
17 Data 0
19 Gnd
21 DRQ 0
23 IOW
25 IOR
27 IORDY
29 DACK 0
31 IRQ 14
33 Add 1
35 Add 0
37 CS 1P
39 IDEACTP
PIN SIGNAL
2 Gnd
4 Data 8
6 Data 9
8 Data 10
10 Data 11
12 Data 12
14 Data 13
16 Data 14
18 Data 15
20 NC
22 Gnd
24 Gnd
26 Gnd
28 +5V
30 Gnd
32 IOCS16
34 Gnd
36 Add 2
38 CS 3P
40 Gnd

P11A - SECONDARY IDE HARD DRIVE CONNECTOR
40 pin dual row header,
Robinson Nugent #IDH-40LP-S3-TR
PIN SIGNAL
1 Reset
3 Data 7
5 Data 6
7 Data 5
9 Data 4
11 Data 3
13 Data 2
15 Data 1
17 Data 0
19 Gnd
21 DRQ 1
23 IOW
25 IOR
27 IORDY
29 DACK 1
31 MIRQ 0
33 Add 1
35 Add 0
37 CS 1S
39 IDEACTS
PIN SIGNAL
2 Gnd
4 Data 8
6 Data 9
8 Data 10
10 Data 11
12 Data 12
14 Data 13
16 Data 14
18 Data 15
20 NC
22 Gnd
24 Gnd
26 Gnd
28 +5V
30 Gnd
32 IOCS16
34 Gnd
36 Add 2
38 CS 3S
40 Gnd

P12 - HARD DRIVE LED CONNECTOR
4 pin single row header, Amp #640456-4

(This connector is used for both IDE and SCSI drives. See JU19 in the Jumpers section.)
PIN SIGNAL
1 +5V Pullup
2 Light
3 Light
4 +5V Pullup

P13 - PCI ULTRA WIDE SCSI CONTROLLER CONNECTOR
50/68 high density SCSI connector, Amp #749069-7
PIN SIGNAL
1 Gnd
2 Gnd
3 Gnd
4 Gnd
5 Gnd
6 Gnd
7 Gnd
8 Gnd
9 Gnd
10 Gnd
11 Gnd
12 Gnd
13 Gnd
14 Gnd
15 Gnd
16 Gnd
17 TERMPWR
18 TERMPWR
19 NC
20 Gnd
21 Gnd
22 Gnd
23 Gnd
24 Gnd
25 Gnd
26 Gnd
27 Gnd
28 Gnd
29 Gnd
30 Gnd
31 Gnd
32 Gnd
33 Gnd
34 WIDEPS
PIN SIGNAL
35 SCZDB12
36 SCZDB13
37 SCZDB14
38 SCZDB15
39 SCZDBPH
40 SCZDB0
41 SCZDB1
42 SCZDB2
43 SCZDB3
44 SCZDB4
45 SCZDB5
46 SCZDB6
47 SCZDB7
48 SCZDBP
49 Gnd
50 Gnd
51 TERMPWR
52 TERMPWR
53 NC
54 Gnd
55 SCZATN
56 Gnd
57 SCZBSY
58 SCZACK
59 SCZRST
60 SCZMSG
61 SCZSEL
62 SCZCD
63 SCZREQ
64 SCZIO
65 SCZDB8
66 SCZDB9
67 SCZDB10
68 SCZDB11

P15 - PCI SVGA INTERFACE CONNECTOR
15 pin VGA connector, Amp #748390-5
PIN SIGNAL
1 Red
2 Green
3 Blue
4 NC
5 Gnd
PIN SIGNAL
6 Gnd
7 Gnd
8 Gnd
9 NC
10 Gnd
PIN SIGNAL
11 NC
12 EEDI
13 HSYNC
14 VSYNC
15 EECS

P16 - PCI 10/100BASE-T ETHERNET CONNECTOR
8 pin shielded RJ-45 connector, Molex #43202-8110
PIN SIGNAL
1 TD+
2 TD-
3 RX+
4 NC
5 NC
6 RX-
7 NC
8 NC

P17 - UNIVERSAL SERIAL BUS (USB) CONNECTOR
8 pin dual row header, Molex #702-46-0821
(+5V fused with self-resetting fuses)
PIN SIGNAL
1 +5V - USB0
3 USB0-
5 USB0+
7 Gnd - USB0
PIN SIGNAL
2 +5V - USB1
4 USB1-
6 USB1+
8 Gnd - USB1

P18 - SYSTEM HARDWARE MONITOR CONNECTOR
6 pin single row header, Amp #640456-6
PIN SIGNAL
1 Gnd
2 GPO (General Purpose Output)
3 CI (Chassis Intrusion Input)
4 FAN1 (Fan 1 Tachometer Input)
5 FAN2 (Fan 2 Tachometer Input)
6 OS# (Temperature Sense Output)

P19 - CPU FAN
3 pin single row header, Molex #22-23-2031
PIN SIGNAL
1 Gnd
2 +12V
3 FanTach

Memory

The DRAM interface consists of two dual in-line memory module (DIMM) sockets and supports auto detection of memory up to 512MB of Synchronous DRAM (SDRAM) for the 440BX or up to 1GB of SDRAM for the 440GX. Minimum memory size is 8MB. The System BIOS automatically detects memory type, size and speed.

The SBC uses industry standard 64-bit or 72-bit wide gold finger DIMM DRAM in two 168-pin DIMM sockets.

NOTE: Memory can be installed in one or both DIMM sockets. If only one DIMM module is used, it must be populated in the top DIMM socket (Bank 1 - BK1). If two modules are used, they must be the same DIMM type, but may be different sizes (see table below). EDO DIMMs are not supported. All DIMMs must have gold contacts.

The SBC supports DIMM memory modules which are PC-100 compliant and have the following features:

  • 168-pin DIMMs with gold-plated contacts
  • 100MHz SDRAM
  • Non-ECC (64-bit) or ECC (72-bit) memory
  • 3.3 volt only
  • Single or double-sided DIMMs in the sizes listed below
  • Buffered or Registered configuration
DIMM Size DIMM Type Non-ECC ECC
8 MB Unbuffered 1M x 64 1M x 72
16 MB Unbuffered 2M x 64 2M x 72
32 MB Unbuffered 4M x 64 4M x 72
64 MB Unbuffered 8M x 64 8M x 72
128 MB Unbuffered 16M x 64 16M x 72
256 MB Registered 32M x 64 32M x 72
512 MB Registered 64M x 64 64M x 72 **

** DP2GX models only

All memory components and DIMMs used with the SBC must be PC-100 compliant, which means that they comply with Intel's PC SDRAM specifications. These include the PC SDRAM Specification (memory component specific), the PC Unbuffered DIMM Specification, the PC Registered DIMM Specification and the PC Serial Presence Detect Specification.

Dimensions




* Intel and Pentium are registered trademarks and Celeron is a trademark of Intel Corporation.

All other product names are trademarks of their respective owners.

DP2 Product Detail.

DP2GX Product Detail.

 

PICMG Single board Computer and Passive Backplane source
Copyright © 2007 Trenton Technology Inc.
Last Updated 6/1/04
CatalogSingle Board ComputersBackplanesCompactPCILinksTechnical Support RequestTerms of UsePrivacy